Materials science and technology : selected, peer reviewed papers from the 2014 2nd International Conference on Advances in Materials Science and Engineering (AMSE 2014), October 1-2, 2014, Dubai, UAE
著者
書誌事項
Materials science and technology : selected, peer reviewed papers from the 2014 2nd International Conference on Advances in Materials Science and Engineering (AMSE 2014), October 1-2, 2014, Dubai, UAE
(Advanced materials research, v. 1064)
Trans Tech Publications, c2015
- : pbk
大学図書館所蔵 全1件
  青森
  岩手
  宮城
  秋田
  山形
  福島
  茨城
  栃木
  群馬
  埼玉
  千葉
  東京
  神奈川
  新潟
  富山
  石川
  福井
  山梨
  長野
  岐阜
  静岡
  愛知
  三重
  滋賀
  京都
  大阪
  兵庫
  奈良
  和歌山
  鳥取
  島根
  岡山
  広島
  山口
  徳島
  香川
  愛媛
  高知
  福岡
  佐賀
  長崎
  熊本
  大分
  宮崎
  鹿児島
  沖縄
  韓国
  中国
  タイ
  イギリス
  ドイツ
  スイス
  フランス
  ベルギー
  オランダ
  スウェーデン
  ノルウェー
  アメリカ
注記
Includes bibliographical references and indexes
内容説明・目次
内容説明
Collection of selected, peer reviewed papers from the 2014 2nd International Conference on Advances in Materials Science and Engineering (AMSE 2014), October 1-2, 2014, Dubai, UAE.
The 37 papers are grouped as follows:
Chapter 1: Materials Science and Technology;
Chapter 2: Applied Mechanics;
Chapter 3: Materials Processing and Manufacturing, Coating Engineering;
Chapter 4: Advanced Materials and Manufacturing Design, Modelling, Simulation Technologies
目次
Preface and Organizing Committee
Chapter 1: Materials Science and Technology
Deterioration of Mortar Composites in Acidic Environment
Evaluation of Friction Coefficient by Ring Compression of Magnesium Alloys
Preservation of Archaeological Leather by Reinforcement with Styrene Butadiene Rubber
Amine-Functionalized Graphene for Natural Gas Sweetening
High Strength and Ductility in Multi-Directional Forged Wrought Aluminum Alloys
Effect of Sintering Time on the Density, Porosity Content and Microstructure of Copper - 1 wt. % Silicon Carbide Composites
Investigation of Non-Monotonic Portions on the Temperature Dependences of High-Temperature Metal Melts' Physical Properties
Non-Destructive Testing for the Evaluation of Pozzolanic Mortar Reinforced to Corrosion
The Abnormal Grain Growth of P/M Nickel-Base Superalloy: Strain Storage and CSL Boundaries
Main Clay Minerals and their Microscopic Morphological Characteristics in Zhangcun Illite Ores
High-Temperature Synthesis of Composite Material from Al-SiO2 System Components
The Synthesis of TiC Powders by Carbothermal Reduction Method in Vacuum
Investigation on the Continuous Microwave Synthesis of Nano Titanium Carbide Powder
Oxidation of Cyclohexene over Mesoporous Silica Pillared Clay Incorporated with Heteropoly Acid Prepared by Sol Gel Method
2D Woven Reinforcements of Natural Fibers
Effect of the Nature of the Layer of Conductive Polymer Composite on the Effectiveness of a Multi-Layer Electromagnetic Shielding
Synthesis of a Novel Structure Carbon Nanocoils and their Application in Photo Diode Devices
Shrinkage Behavior of Composite Geopolymer Mortar Cured at Different Relative Humidities
Chapter 2: Applied Mechanics
Vibromechanic Way to Remove Residual Stresses
Fatigue Life Prediction of Composite Laminates Based on Progressive Damage Analysis
Research on Calculation of Equivalent Damping Ratio of Electrical Transmission Tower-Line System with Viscoelastic Dampers
The Impact of Pre-Heating on Pressure Behavior in Tapered Cylindrical Die in Pultrusion of Large-Sized Composite Rods
Chapter 3: Materials Processing and Manufacturing, Coating Engineering
Influence of Stacking Fault Energy on the Grain Size of FCC Metals Fabricated by Accumulative Roll Bonding Process
Blast-Hole Cuttings Grindability Relationship with Silica Content and Bit Wear Rate
Surface Modification of Broaches from the Powder High Speed Steels Applied to Processing of Aviation Products from Heat-Resistant Alloys
High-Strength Ceramic Cutting Tools with Multipurpose Coatings for Highly Effective Processing of Tempered Steel
Options for Forming of Nanostructured Surface Coatings
Technological Features of Obtaining of Nanostructured Coatings on TiNi Base by Magnetron Sputtering
Micro- and Nanostructure of Titania Coatings Modified with Functional Ceramic Nanoparticles
Effective Use of Technology Flowdrill in Production Engineering
The Precision Forging Experiment of Mg Alloy Drop Forging Using Computer Simulation
Chapter 4: Advanced Materials and Manufacturing Design, Modelling, Simulation Technologies
A Precise and Efficient Method to Manipulate the Amplitude of Parabolic Function of Transmission Errors
High Performance Nanostructured Silicon Oxide Impedance Biosensor System with Online Noise Spectroscopy Analysis
Ocean Surface Rendering Method Based on Mild-Slope Equation
Comparative Study of Microcantilever-Based Sensor for Biosensing Applications
Micro Fluidic Oscillator: A Technical Solution for Micro Mixture
A Hardware-in-the-Loop Simulation Test Bench for Subway Train Brake Systems
「Nielsen BookData」 より