Advances in materials and manufacturing : selected, peer reviewed papers from the International Conference on Advances in Materials and Manufacturing Engineering (ICAMME-2014), December 19-20, 2014, Chennai, India
著者
書誌事項
Advances in materials and manufacturing : selected, peer reviewed papers from the International Conference on Advances in Materials and Manufacturing Engineering (ICAMME-2014), December 19-20, 2014, Chennai, India
（Applied mechanics and materials, v. 766-767）
Trans Tech Publications, c2015
- : [set]
- Part 1
- Part 2
- タイトル別名
-
ICAMME 2014
大学図書館所蔵 件 / 全1件
-
該当する所蔵館はありません
- すべての絞り込み条件を解除する
注記
Includes bibliographical references and indexes
内容説明・目次
内容説明
Collection of selected, peer reviewed papers from the International Conference on Advances in Materials and Manufacturing Engineering (ICAMME-2014), December 19-20, 2014, Chennai, India.
The 193 papers are grouped as follows:
Chapter 1: Hybrid and Composite Materials;
Chapter 2: Natural Fibre Composites;
Chapter 3: Metal Matrix Composites;
Chapter 4: Nano-Scale Materials and Technologies;
Chapter 5: Material Characteristics;
Chapter 6: Application of Phase Change Materials;
Chapter 7: Materials Application and Utilization;
Chapter 8: Advances in Coating and Surface;
Chapter 9: Advances in Cutting and Machining Processes;
Chapter 10: Advances in Welding Process;
Chapter 11: Advances in Drilling Process;
Chapter 12: Optimization of Processing Technologies;
Chapter 13: Numerical Investigations and Algorithms;
Chapter 14: Design, Modeling and Simulation;
Chapter 15: Applied Mechanics and Mechanical Engineering;
Chapter 16: Manufacturing Technology;
Chapter 17: Manufacturing Management
目次
Preface and Committee Members
Chapter 1: Hybrid and Composite Materials
Characterisation of Dicyclopentadiene Filled Microcapsules for Self-Healing Composite Materials
Comparative Vibration Analysis of Multilayered Filament Wound Composite Cylinders with Various End Conditions
Identification of Damage for a Single and Double Edge Cracks in a Laminated Composite Beam by Using Harmonic Analysis
Stress Analysis and Progressive Failure Analysis of Multilayered Basalt/Epoxy Composites
Mechanical Performance of Polycarbonate/ABS, Glass Filled Polycarbonate Blends - Review
Investigations on Wear and Frictional Characteristic of Hybrid Polymer
Parametric Optimization of AWJM in AA6351-SiC-B4C Hybrid Composite Using Grey Relational Analysis
Tensile Property Evaluation of Woven Glass Fiber Reinforced Plastic and Aluminium Stack
Hybrid Nanocomposites - A Review
Investigation on Tensile Strength of Water Hyacinth - Coconut Shell Powder Reinforced Hybrid Eco Composite
A Study on Uniform Performance of Carbon - Carbon Matrix Composites with Ceramic Reinforcements
Evaluation of Tensile Behaviour of GFRP/SiC Polymer Reinforced Composites
Chapter 2: Natural Fibre Composites
Effect of Fibre Orientation on Specific Gravity, Hardness, Flexural Strength and Tensile Properties of Jute/Hemp Hybrid Laminate Composite
Evaluation of Mechanical Properties of Teak Wood Saw Dust - Cashew Nut Shell Liquid Resin Composites
Evaluation of the Double Shear and Hardness of Abaca and Flax Reinforced Polymer Composite for Automotive Applications
Flexural, Tensile and Impact Properties of Alkali Treated Coir Fibre Composites Prepared by Compression Molding Technique
Investigation of Tensile Properties of Manila Fibre Reinforced Composite
Mechanical and Cure Characteristics of Natural Rubber Composites with Caryota Fibre Incorporated in Dry Stage and Latex Stage
Mechanical Behaviour of Sugarcane Bagasse and Banana Fibers Reinforced Composite
Mechanical Characteristics of Woven Banana and Glass Fiber Epoxy Composites
Predicting the Best Tensile Strength of Banana-Bamboo-Glass Fiber Reinforced Natural Fiber Composites Using Taguchi Method
Preparation and Mechanical Characterization of Jute-PP and Coir-PP Bio-Composites
Tensile Properties of Natural Fiber Reinforced Polymers: An Overview
Investigation of Tensile Behaviour of Flax - Abaca Hybrid Epoxy Composite
Processing and Mechanical Property Evaluation of Flax-Glass Fiber Reinforced Polymer Composites
Experimental Investigation on Buckling Analysis of Woven Glass Fiber/Epoxy Laminated Composite Materials
Influence of Fiber Reinforcement and Abrasive Particle Size on Three-Body Abrasive Wear of Hybrid Friction Composites
Predicting the Best Flexural Strength of Banana-Bamboo-Glass Fiber Reinforced Natural Fiber Composites Using Taguchi Method
Experimental Investigation on Mechanical Properties of Hemp-Banana-Glass Fiber Reinforced Composites
Mechanical & Thermal Properties of Sisal Epoxy/Banana Epoxy Composites - A Review
Flexural and Impact Properties of 2D and 3D Jute/GF/Epoxy Hybrid Composite Materials
Investigation of Flexural Characteristics of Flax and Abaca Hybrid Epoxy Composites
Processing and Mechanical Property Evaluation of Kenaf-Glass Fiber Reinforced Polymer Composites
Synthesis and Characterization of Multi Wall Carbon Nanotube (MWCNT) Filled Hybrid Banana-Glass Fiber Reinforced Composites
Assessing of Mechanical Properties of Natural Fiber Reinforced Polymer Matrix Hybrid Composites
Fourier Transform Infra-Red Spectroscopy and Chemical Resistance of Untreated and Alkali Treated Coconut Leaf Sheath Fiber Reinforced Polymer Composites
Study of Mechanical Properties of Jute-Banana-Glass Fiber Reinforced Epoxy Composites under Various Post Curing Temperature
Chapter 3: Metal Matrix Composites
A Study on Dry Sliding Wear Behaviour of Hybrid Metal Matrix Composites at Room Temperature
A Study on Machinability Performance of Silicon Carbide Paticulate Reinforced Metal Matrix Composite
Aluminium Metal Matrix Composite - An Insight into Solid State and Liquid State Processes
Effect of Steel Slag on the Impact Strength of Aluminium Metal Matrix Composite
Evaluation of Mechanical Properties of Aluminium Alloy 7075 Reinforced with SiC and Al2O3 Hybrid Metal Matrix Composites
Investigation of Tensile Property of Aluminium SiC Metal Matrix Composite
The Mechanical Characterization of Al2O3 Reinforced AL6061 Metal Matrix Composite
Effect of Volume Fraction on Surface Roughness in Turning of Hybrid Metal Matrix (A6061 A1+SiC+Graphite) Composites
Tribological Behaviour of Hybrid (Al356 + SiC + Gr) Metal Matrix Composites
The Comparative Analysis of Mechanical Properties on MMC (AA6061 + SiCp 10% wt) before and after Age Hardening
Development of Magnesium Matrix Syntactic Foams Processed through Powder Metallurgy Techniques
Experimental Investigation of Mechanical and Chemical Properties of Aluminium Reinforced with MWCNT
Effect of Silicon Carbide (SiC) on Stir Cast Aluminium Metal Matrix Hybrid Composites - A Review
Microstructural and Mechanical Behaviour of Aluminium Matrix Composites Reinforced with Coated SiC Particles Fabricated by Stir Casting
Microstructure and Mechanical Properties of Al6061-Graphite Composites Fabricated by Stir-Casting Process
Production and Characterization of Aluminium Metal Matrix Composite Reinforced with Al3Ni by Stir and Squeeze Casting
Tribological Performance and Microstructural Analysis of an Aluminium Alloy Based Hybrid Composite Produced by P/M
Effect of Abrasive Grain Size of the AWJM Performance on AA(6351)-SiC-B4C Hybrid Composite
Chapter 4: Nano-Scale Materials and Technologies
Analysis of Mechanical Properties and Morphological Study of Coated Ceramics Using Multiwall Carbon Nanotubes with Aluminium Alloy
Application of Nanofluids as Coolant in Automobile Radiator - An Overview
Emission Control in Two Wheelers Using Magnesium Nanoparticle as a Catalyst
Experimental Study of Preparation, Characterisation and Thermal Behaviour of Water-Based Nanofluids Containing Titanium Oxide Nanoparticles
Investigation of Mechanical Properties of Nano Sized Clay/LDH Particle as Hybrid Nano Composite Material
Material Characteristics of Fabricated Resin Carbon Nanotube Reinforced and Resin Glass Fiber Carbon Nanotube Reinforced Composites
Morphological Study of Coated Silicon Carbide Particle with Multi Wall Carbon Nano Tubes
Tensile and Flexural Properties of Glass Fibre Reinforced Nano Polymer Composite Panels
Vulcanization, Mechanical and Dielectric Properties of Carbon Black/Nanoclay Reinforced Natural Rubber Hybrid Composites
Experimental Study on Mechanical Properties of PA66 Blended with MWNTs
Effects of Nano-Sized Metal Oxide Additive on Performance and Exhaust Emissions of C I Engine
Chapter 5: Material Characteristics
Characterization of Al-17wt.%Si Using Centrifugal Casting
Effect of Mold Material on Boundary Heat Flux Transients during Gravity Die-Casting
Effects of 4.5% Copper Addition and Melt Treatment on Microstructure and Wear Properties of Al-7Si Alloy
Formability Analysis of AA6061 Sheet in T6 Condition
Experimental Study of Squeeze Casting of Aluminium Alloy AA6061
Investigation on the Laser Based Actuation of Single way Trained SMA Sheet and their Application for the Development of Micro Positioning Stage
Tribo-Thermal Based Evaluation of Non Asbestos Disc Brake Pad Formulation
Development and Characterization of Al-Si-Cu FGM Using Centrifuge Technique
Chapter 6: Application of Phase Change Materials
Experimental Analysis of Storage of Solar Energy in Phase Change Materials Encapsulated in Copper Cylinders
Experimental Investigation of Solar Paraffin Wax Melting Unit Integrated with Phase Change Heat Energy Storage by Using Phase Change Material
Experimental Investigation on Enhancement of Heat Transfer in Thermal Energy Storage System Using Paraffin Wax as PCM
Experimental Study on Solar Cooker Using Phase Change Materials
Numerical Investigation on Vertical Generator Integrated with Phase Change Materials in Vapour Absorption Refrigeration System
Review on Phase Change Materials in Thermal Energy Storage System
Different Aspects of Phase Change Material Encapsulation for Sub Cool Thermal Storage - A Review
Chapter 7: Materials Application and Utilization
Advances in Photovoltaic Materials for Building Integration
Effect of Spillway Materials in Air-Water Interactions
Fabrication of Hydraulic Bumper for Anti-Collision in a Vehicle
Experimental Investigation on the Effect of Fill Materials in Cooling Towers
Applications of Cellular Materials - An Overview
Evaluation of Recast Layer Thickness of Electrical Discharge Machined AISI 202 Stainless Steel with Various Pulse Generators
Study of Composite Helical Spring Using Glass Fibre with Araldite LY556 and XY54
Micro Cantilever CO2 Gas Sensor Based on Mass
Analysis of Various Materials for Service Platform in Wind Turbine Generator
Influence of Nd: YAG Laser Parameters on Tensile Behaviour, Microhardness and Surface Roughness of Ni-Cr Alloy for Dental Prostheses
Effect and Optimization of Performance of Ceramic Coated Internal Combustion Engine
Formation of Bio-Fuel from Waste Plastic Scrap
Performance and Emission Characteristics of a Mixed Biodiesel Fueled CI Engine
Research in the Area of Material Failure in Aeroengine
Chapter 8: Advances in Coating and Surface
Atomic Force Microscopy Study on WC 14Co and WC 14Co+CNT Coated Surfaces
Determination of Abrasive Wear Resistance of Plasma Sprayed Coatings on Stainless Steel Substrate
Dry Sliding Wear Behaviour of Al2O3 Coatings for AISI 410 Grade Stainless Steel
Effect of Plasma Spray Process on TiO2 Coating over Mild Steel Substrate
Performance Evaluation of Hard Turning for AISI M2 Die Steel with Coated and Non-Coated CBN Inserts
Performance Study on Copper Coated Tool Using Powder Mixed EDM of Monel 400
Investigation of Morphological and Mechanical Features of Polyurea
Effect on Performance and Emission Analysis of Advanced Ceramic Material Coated Piston Crown Using Plasma Spray Coating Techniques
A Review on Surface Engineering of Ti6Al4V Titanium Alloy Using Gas and Laser Nitriding Techniques
Chapter 9: Advances in Cutting and Machining Processes
A Review on Abrasive Jet Machining Process Parameters
A Review on Applications of Image Processing in Inspection of Cutting Tool Surfaces
Review on Machining Aspects in Metal Matrix and Ceramic Matrix Composites Using Abrasive Waterjet
Hard Turning of AISI D2 Steel by Polycrystalline Cubic Boron Nitride (PCBN)
Torsional Extrusion Processing of Titanium Alloy Ti 6Al-6V-2SN under High Feeding Rates
Effect of Process Parameters on Wear Performance in Abrasive Flow Machining
Effects of Electrical Process Parameters and Electrode Tool Geometries in EDM of Inconel825 Material Using Zirconium Copper Electrode
Performance and Analysis of Silicon Mixed Kerosene Servotherm in EDM of Monel 400
Fuzzy Modeling of Surface Roughness Parameters in Machining Ti-6Al-4V Alloy
Influence of Particle Fracture on the Slurry Abrasion Behavior of Weld Deposited Martensitic Steel
Chapter 10: Advances in Welding Process
Comparative Study and Analysis of Friction Stir Welding with Plasma ARC Welding
Effect of Process Parameters on Mechanical Characterization of Dissimilar Friction Stir Welded Aluminium Alloys
Heat Reduction in a Tool Holder during Friction Stir Welding of Aluminium Alloy
Investigations on the Effect of Tool Geometries on Friction Stir Welded 5052 H32 Aluminium Alloy
Optimization of Process Parameters for Friction Stirs Welding of Aluminium Alloy Al 6061
Investigating the Weld Strength of AA7075 Aluminium Alloy for TIG, MIG and FSW Welding
Stress Corrosion Cracking Behaviour of Flux Bounded TIG Welded AA2219 T87 Aluminum Alloy in 3.5 Weight Percent NaCl Solution
Comparative Study of Ti Alloy and Stainless Steel 304L Friction Welded Joint with Different Interlayer Process Methods
Influence of Process Parameter on Microstructural Characteristics and Tensile Properties of Friction Welded ASS304L Alloy
Laser Assisted Brazing of Ceramic and Titanium Alloy Using Cu-Ag Filler Material
Sensitivity Analysis of Friction Welding Process Parameters on Tensile Properties of ASS304L Alloy
Developing the Empirical Relationship to Predict the Minimum Microhardness of AISI 1020 Grade Low Carbon Steel Joints
Investigation of Microstructure and Mechanical Properties of Resistance Spot Welded Dissimilar Joints Between Ferritic Stainless Steel and Weathering Steel
Characterization of Duplex Stainless Steel/Cold Reduced Low Carbon Steel Dissimilar Weld Joints by GTAW
Chapter 11: Advances in Drilling Process
Cutting Force Analysis in Drilling of Al6061/Mica Particulate Composite
Delamination in Drilling of Natural Fibre Reinforced Polymer Composites Produced by Compression Moulding
Experimental Investigations on Drilling Characteristics of Cenosphere Reinforced Epoxy Composites
Investigations of Damages during Drilling of Natural Sandwich Composites
Micro-ECM Drilling of Copper Alloy and Taguchi Optimization
Modeling of Delamination in Drilling of Particleboard (PB) Composite Panels
Modeling of Surface Roughness in Drilling of MDF Panels
Roughness Analysis of the Holes Drilled on Al / SiC Metal Matrix Composites Using Atomic Force Microscope
Roundness Error Evaluation in Drilling of Glass Fiber Reinforced Polypropylene (GFR/PP) Composites Using Box Behnken Design (BBD)
Study on Drilling of Al/Al2O3/Gr Hybrid Particulate Composites
Chapter 12: Optimization of Processing Technologies
Application of Taguchi-Grey Relational Methodology for Multiple Optimal Performance Measures in WEDM Process
EDM Process Parameters Optimization Using Taguchi Method
Modeling and Optimization of WEDM of Titanium
Optimisation of Shutter Speed in Machine Vision Technique for Monitoring Grinding Wheel Loading
Optimization of Friction Welding in Dissimilar Materials through Taguchi Based Grey Relational Analysis
Optimization of Impact Strength in Dissimilar Materials by Using Friction Welding Process
Optimization of Linear Layout Problem in Flexible Manufacturing System Using Evolutionary Algorithms - Case Study
Surface Roughness Optimization of Wire Electrical Discharge Machining Using ABC Algorithm
An Investigation of the Influences of EDM Parameters and Tool Geometries on Radial Overcut for Monel 400 Material with Tungsten Copper Electrode
Computational Intelligence in Optimization of Process Parameters in Turning Metals and Composites - A Review
Multi Response DEA-Based Taguchi Optimization of Process Parameters on AA8011 Friction Stir Welded Aluminium Alloys
Quality Improvement of Sugar by Two Factor Factorial Experimentation in Optimization of Quantity of Lime and Sulphur Added in the Juice Sulphitation Process of a Sugar Plant
Minimizing of Rejection in Cylinder Head Machining Using the Anova Method
Chapter 13: Numerical Investigations and Algorithms
Applications of Super Strongly Perfect Graph for Manufacturing System towards a Leaner Structure
Modeling and Analysis of Cutting Force in Turning of AISI 316L Stainless Steel (SS) under Nano Cutting Environment
Investigation of Particle Segregation and Solidification Time in FGM's Using Centrifuge Casting Technique
Optimization of Two-Stage Hybrid Flow Shop Scheduling Problems Using Genetic Algorithm
Optimization of the Location of Secondary Sources for the Active Engine Vibration Acoustic Noise Control in the Generator Room
Theoretical Prediction of Thickness Distribution on Warm Deep Drawn AISI 304 Steel Cup
Investigation of Multi-Dimensional Cellular Manufacturing System Using Meta-Heuristic Method
Scheduling to Minimize the Sum of Weighted Total Flow Time and Makespan in a Permutation Flow Shop with Setup Time
Taguchi Based Optimization of Engine Parameters Using Nanocatalyst with Blends of Biodiesel
Chapter 14: Design, Modeling and Simulation
A New Artificial Immune Algorithm for Solving Gear Design Problem
An Integrated Approach for the Sustainable Development of an Automotive Component Using CAD/CAE, DFE and DFMA Concept
Computer Aided Modelling and Design of Mechanical Configuration of an Inspection Robot
Design and Analysis of an Intake Manifold in an IC Engine
Design and Manufacturing of Conical Vent Profile Disc Brake
Design Optimization of Spur and Helical Gear Pairs
Numerical Simulation on Hypersonic Combustion of Hydrogen-Fueled Scramjet Combustor with Parallel Strut Fuel Injection at a Flight Mach Number of 7
Three Dimensional Simulation of Air Bleed Duct under Deep Drawing of Ti 6Al-6V-2SN
Computer Aided Modelling and Static Analysis of an Inspection Robot
Computational Analysis of Different Shapes of Dimple on Wing
Contact Stress Analysis of a Helical Gear
Prediction of Surface Roughness in Magneto Rheological Abrasive Flow Finishing Process by Artificial Neural Networks and Regression Analysis
Stress Analysis of Aluminium Reinforced Air Springs
Thermal and Vibrational Analysis of Cubesat
Optimal Manufacturing Cost and Quality Loss by Reciprocal Exponential Cost-Tolerance Function
Conceptual Design of Iron Box Handles with Ergonomic Aspects
Finite Element Analysis and Formability Test on Incremental Forming of IS:513 CR3 Steel Sheets
Finite Element Analysis and Simulation of Al 7075 Alloy Joints Produced by Friction Stir Welding
Fatigue Analysis of Forward Fuselage under Dynamic Conditions
Determination of Fracture Behavior under Biaxial Loading of Kevlar 149
Computational Investigation of High Velocity Ballistic Impact Test on Kevlar 149
Chapter 15: Applied Mechanics and Mechanical Engineering
Acoustical Failure Diagnosis of Bush in a Domestic Mixer
The Consequence of Target Surface Curvature in the Jet Impingement Cooling
Performance Combustion and Emission Characteristics of DI Diesel Engine with Use of Alternate Mechanism
Productivity Improvement in CED Paint Plant by Jig Modification
A Case Study on Scrap Reduction of Transfer Pump in Common Rail Fuel Pump
Entropy Generation Analysis of 10Wp Photovoltaic Thermal Hybrid System
Chapter 16: Manufacturing Technology
Evolution of Robust Manufacturing Process in Machining of DC Motor Commutator Using Complementing Problem Solving Tools
Innovative Approach in Introducing Lean Manufacturing Tools in Maintenance of Aircraft
Wastage Reduction through Lean Manufacturing in Head Lamp Casing Manufacturing Process
Selection of Manufacturing Method Using Artificial Neural Network
Chapter 17: Manufacturing Management
Solving Multi Objective Job Shop Scheduling Problems Using Artificial Immune System Shifting Bottleneck Approach
Questionnaire Development for the Evaluation of Agility Index in an Original Equipment Manufacturing (OEM) Industry
「Nielsen BookData」 より