Urgent problems of up-to-date mechanical engineering : selected, peer reviewed papers from the International Conference "Urgent Problems of Up-to-Date Mechanical Engineering", UTI TPU, December 11-12, 2014, Yurga, Russia
著者
書誌事項
Urgent problems of up-to-date mechanical engineering : selected, peer reviewed papers from the International Conference "Urgent Problems of Up-to-Date Mechanical Engineering", UTI TPU, December 11-12, 2014, Yurga, Russia
（Applied mechanics and materials, v. 770）
Trans Tech Publications, c2015
- : pbk
大学図書館所蔵 件 / 全1件
-
該当する所蔵館はありません
- すべての絞り込み条件を解除する
注記
Includes bibliographical references and indexes
内容説明・目次
内容説明
Collection of selected, peer reviewed papers from the International Conference "Urgent Problems of Up-to-Date Mechanical Engineering", UTI TPU, December 11-12, 2014, Yurga, Russia.
The 133 papers are grouped as follows:
Chapter 1: Materials Science in Mechanical Engineering;
Chapter 2: Metal Processing in Mechanical Engineering;
Chapter 3: Designing and Modelling of Machines and Mechanisms;
Chapter 4: Mechatronics, Automation and Control;
Chapter 5: Industrial Engineering and Environmental Research
目次
Preface and Committees
Chapter 1: Materials Science in Mechanical Engineering
Microsilica as a Modifying Component in Fired Ceramics
Modern Approaches to Efficient Use of Mn-Containing Raw Material in Steel Production
Nitrogen Alloying of Steel by Blowing in the Ladle through Bottom and Submersible Tuyeres
Influence of High-Concentrated Heat Sources on Alloying Elements Transition into the Weld Metal
Preparation of Copper Electroerosion Nanopowders from Waste of Aquatic Medium and its Validation by Physicochemical Methods
Methods for Defining the Concentration of Nanostructured Powders in Protective Gas and its Effect on the Microstructure of Deposit Metal
Increasing Machining Efficiency of Components Made from Hard-Processing Materials
New Multilayer Corrosion Resistant Materials for Nuclear Power Engineering
Electrochemical Research of the Multilayer Corrosion Resistant Material
Steel GX120Mn12 Modifying by Ultra Disperse Powders of Refractory Metal Oxides
Distributive Characteristics of Gas Phase in a Liquid when Bottom Blowing
Acoustic Emission Diagnostics of the Destruction of Welded Joints Stainless Steel Pipes Arising Welding
Technology of Residual Stresses Relaxation by the Ultrasonic Vibrations
Influence of Arc Welding Power Supply on Structural Phase Composition of X12CrNiTi 18-9 (DIN) Weld
The Analysis of Microstructure and the Properties of the Metallic-Matrix Composite on the Basis of the Copper and Aluminum Oxide
Structural Aspects of Zr+ Ion-Beam Surface Modification and Mechanical Properties of 12CrMoV Steel
Tribomechanical Properties of Polymeric Composites Based on Mixture of Ultra High Molecular Weight Polyethylene and Polyamide
Functionalized Composite Coatings Based on Filled Powder Paint Processed in Planetary Ball Mill
Use of Nanopowders of Metals in Different Branches of Industry
Smelting Steel Resistant to Corrosion from Metal Mixing Air in Late Oxygen Blowing
Industrial Surfacing of Hammer Grinder Components Utilized in Coke-Making Process and Outlines of Surfacing Quality Improvement
Combined Steel Treatment with Calcium-Silicon
New Technologies of Anodizing Components of Oil and Gas Industry Equipment Made of Aluminum Alloys
Impact of Welded Joint on Cyclic Strength of Low-Alloyed Steels
Development of the Technique to Simulate Residual Heading Corium Prototype
Elastic Properties of Solid Solutions with Intermediate Valence Sm1-xYxS
Formation of Nano-Sized Structural-Phase States in Surface Layers of a Cermet Alloy and the Influence of the States on the Tool Life of Cermet Plates in Metal Cutting
The Analysis of Microstructure and the Properties of the Metallic-Matrix Composite on the Basis of the Copper and Aluminum Oxide
Application of Natural Barium-Stroncium Containing Material for Steel Treatment
Cutting Forces Calculation at Diamond Grinding of Brittle Materials
Numerical Simulation for Deformation of Polymer Samples Using the Split Hopkinson Pressure Bar Technique
Explosive Compaction of Solid Inert Three-Component Mixtures Taking into Account a Different Thickness of the Explosive Axial Layer
Acoustic and Elastic Properties of Cu3Au Alloyin in the Field of High Temperature
Fiber-Reinforced Composites in Rapid Prototyping Technologies
Controllable Decomposition in Ahm Crystals in Ultraviolet Radiation
Investigation of High-Strength and Heat-Proof Added Metal Characteristics with Thermal Microscopy Facilities
Experimental Study of Plastic Deformation Intensity in Cutting Zone
Influence of Layer Laser Sintering on Quality of Surface Layer Sintered Aluminum Powder PA-4
Effect of Load Ratio on Fatigue Failure Micromechanisms of Railway Axle Steel
Methods of Considering Reliability in the Quality Evaluation Procedure for Composite Metal Cutting Tools
Chapter 2: Metal Processing in Mechanical Engineering
Analysis of Results of Computer Simulation of the Casting Process
Interval Objects and Operations in Deformable Solid Mechanics Problems
The Mathematical Model of Metal Melt State under Induction Melting
Burnishing Tool Face Optical Control Method
Study of Wind Velocity Impact upon the Quality of Shielding and upon the Thermal Processes under MAG Welding
The Theoretical Principles of Sheet Metal Forming Processes Intensification Based on Anisotropy
Design of Straight Tooth Profile for Fine-Module Ratchet Teeth
The Influence of Melting Technology and Out-of-Furnace Treatment on Composition of Nonmetallic Impurities in Rail Electric Steel
Research of Hardalloyed Burnishing Tool Durability with Coatings by Ion-Plasmous Sputtering Method
A Change in Mechanical Behavior of Safety Fluid Couplings when the Lockup Device is Used in its Construction
Parameters of Contact Interaction while Lathing with Straight-Edge and Radius Cutters
Segmentation and Statistical Processing of Geometric and Spatial Data on Self-Organized Surface Relief of Statically Deformed Aluminum Alloy
Resilience Tests of Milling Cutters with Constructive Feed
Application of Inorganic Nanopowders in Welding, Surfacing and Spraying (Review)
Influence of Preliminary Deformation on Micromechanisms of Failure of Offshore Gas Pipeline Material
On the Design of Composite Active Part of Cutting Tools
Chapter 3: Designing and Modelling of Machines and Mechanisms
The Process Model of Diesel Engines in Low-Pressure Channels under the Conditions of Subzero Temperature
Electronic Circuit Design of Power Supplies for Welding in Ltspice Iv Program
Designing Self-Balanced Spatial Mechanisms
Providing of High Longevity of Operating Parts of Small-Scale Machinery in Agriculture
Peculiarities of Operation of Disc Springs Made of Alloys with Shape Memory Effect
Mathematical Modeling of the Dynamics of a Two-Mass Gear System with Consideration of Shaft Compliances
Physical Modeling of Fluid Flow in the Near-Wellbore Formation Zone on the Basis of Equivalent Materials
Modeling of the Potential Pit and Force Field to Limit the Motion of the Plasma Particles
Operating Mode Simulation of the Micro HPP Hydro-Generator
Application of Numerical Analysis for Physical and Chemical Combustion Processes in Design of Boiler Units
Computational Simulation of the Mechanical Equipment's Dynamic and Strength Characteristics
Studying Characteristics of Traction Induction Motors for Variable-Speed Mine Electric Locomotive
Simulation of Geokhod Movement with Blade Actuator
Geokhod Propel Effort Mathematical Model
Modeling of Surface Topography after Burnishing Processing
Comparative Analysis of the Lip Seal in Hydraulic Power Cylinder
Determination of Kinematic Parameters of Rotary Transmission Tooled with Hydraulic Cylinders
Modelling of Hydraulic Pulse Systems of Drilling Machines with Pneumatic Spring
Development Process Design with Effects of Technology Quality
Mathematical Modeling and Experimental Evaluation of the Stress in the Connecting Elements of the Rods at a Rotational-Impact Loading
Finite Element Models of Disk Tools with Attachment Points on Triangular Prisms
Stress State of Disk Tool Attachment Points on Tetrahedral Prisms between Axial Bits
Determining Deviations in Geometry of the Geokhod Shells
Effect of Operating Stresses on Elements of Shovel Swing Bearings
Mathematical Model of Thermal Physics of the Dual-Cycle Cooling System of the Tool for Pieces Nanostructuring Burnishing
The Numerical Analysis of Accuracy of Hydraulic Leg Cylinder in Modeling Using Solid Works Simulation
Computer Simulation of Strain at Drilling with PDC Bits
FEM Study of Stress-Strain State of Elements of Harmonic Gear Drive with Hollow Shaft and Intermediate Rollers
The Compound Hob for Processing Gearbox Pinions Used in Hoist for Well Repairs
Simulation of the Technological Process of the Strengthened Treatment of the Drill Pipes Thread
Numerical Analysis of Gasdynamic Characteristics of Vortex Ring
Chapter 4: Mechatronics, Automation and Control
A Parallel Implementation of 3D Computed Tomography Algorithm
Algorithm of Route Position's Detecting for Service Transport
A Method of Industrial Image Processing Based on Enhancement of Object Boundaries
Methods Local Analysis and Processing of Acoustic Signals in the Diagnosis of Conditions Technical Systems and Telecommunications
Development of Method of Rapid Analysis of Particle Size Distribution of the Coal Charge Based on Digital Image Processing
The Influence of Power Mode on Ir-Leds Resistance to the Irradiation with Fast Neutrons
Effects of P-N Junction Built-In Electric Field on Ir-Led Resistance under Gamma Rays Irradiation
Preliminary Medical Studies of Electrocardiograph on Nanosensors
Analysis of Control Problems for 2-D Model of Sound Scattering
Control Problems for 2-D Electromagnetic Wave Scattering Model
Study on Neural Networks Usage to Analyse Correlation between Spectrum of Vibration Acceleration Signal from Pin of Ball Mill and its Filling Level
Research Data of Turbine Nozzles of 5-9 Degree Outlet Angles
Determination of Load Performance of Two-Bar Girder Lining to Support the Contour Zone
Efficiency of the Determined Model of Power Consumption by Nonlinear Closed Slow-Response Production
Numerical Optimization Method of Spacecraft Antenna Retargeting Point Calculations
Electromagnetic Method for Resonance Tuning of a Mechatronic System
The Model for Estimate of Cylindrical Machined Surfaces Parameters
An Algorithm for Determining the Position and Orientation of 3-D Objects from Images Using Spectral Graph Theory
Accelerometric Method of Measuring the Angle of Rotation of the Kinematic Mechanisms of Nodes
Research and Development of Algorithms for Digital Localization of Metal Castings
The Algorithm for Generating Pairs of Projections of Three-Dimensional Objects on Two Images
Prospects of Creating Products Using Selective Laser Sintering
Monitoring Positioning Accuracy of the Basic Functional Units of Technological Machines
Simulation of Technological Systems for Diagnosis and Management Machining with CNC
Engineering and Technology Based on Rapid Prototyping
Diagnosis of Transformer Winding for Presence of Defects in the Form of Closed Loop Coil
Optimization Approach in Identification Problems for Stationary Convection-Diffusion Model
Chapter 5: Industrial Engineering and Environmental Research
The Ratio-Delay Method of the Manufacturing System Analysis
Decision Making Models on the Basis of Expert Knowledge for an Engineering Enterprise Strategic Management
Using of Information Systems for Socio-Economic Management Applications in Mechanical Engineering Enterprises
The Models of Supporting the Strategic Decisions on Engineering Products Competitiveness
Optimization of Products Life Cycle
State and Business Partnership as an Adaptation Instrument of Mechanical Engineering and Power Engineering Sector towards Global Climate Changes
The Resistive-Acoustic Method of Monitoring Industrial Sludge Plume
Environmentally-Atmospherical Monitoring of Industrial Machine Builder State
Indirect Negative Influence of Coal Mine Motor Vehicles on the Environment
Numerical Analysis of Inverse Problems for the Model of Transfer of Industrial Environmental Pollution in the Machine-Building
The Subjects of Automated Competitiveness Monitoring of Science-Intensive Products in Engineering
Process Water Treatment at Metallurgical and Machine Building Enterprises
Prospects of Galvanic Sludge Recycling
Lean Principles-Based Optimization of the Manufacturing System
Consideration of Exploration Information Reliability when Forming the Requirements to the Mining Equipment in Coal Industry
Calculation of Grillage Strip Foundation in Area of Karst Collapses Formation
Development of a System of Self-Assessment Indicators and its Optimization with the Help of Rasch Model
Improvement of the Air Depression Survey at the Discharge, Suction and Combined Methods of Air Flow
Automation Tool Preparation in the Conditions of Production
「Nielsen BookData」 より