Key engineering materials V : selected, peer reviewed papers from the 2015 5th International Conference on Key Engineering Materials (ICKEM 2015), March 21-23, 2015, Singapore
Author(s)
Bibliographic Information
Key engineering materials V : selected, peer reviewed papers from the 2015 5th International Conference on Key Engineering Materials (ICKEM 2015), March 21-23, 2015, Singapore
（Advanced materials research, v. 1119）
Trans Tech Publications, c2015
- : pbk
Available at / 1 libraries
-
No Libraries matched.
- Remove all filters.
Note
Includes bibliographical references and indexes
Description and Table of Contents
Description
Collection of selected, peer reviewed papers from the 2015 5th International Conference on Key Engineering Materials (ICKEM 2015), March 21-23, 2015, Singapore.
The 159 papers are grouped as follows:
Chapter 1: Nanoscale Materials and Technologies;
Chapter 2: Polymeric and Composite Materials and Their Properties;
Chapter 3: Investigations in Rubber Based Materials;
Chapter 4: Surface Engineering and Technologies of Coating;
Chapter 5: Bio- and Eco Materials;
Chapter 6: Metals and Alloys, Industrial Chemical Technologies;
Chapter 7: Technologies of Materials Processing;
Chapter 8: Materials and Related Technologies in Construction;
Chapter 9: Physical Properties of Materials in Mechanical Engineering
Table of Contents
Preface, Committees and Sponsors
Chapter 1: Nanoscale Materials and Technologies
Metal Nano Particles Formation on Rotating Powder (NPP) Substrate in Physical Vapor Deposition
Comparative Studies of Nanostructured Aluminum Alloys by Destructive and Nondestructive Testing
Instant Microwave Synthesis of Titania Nanoflowers for Application in DSSCs
Sensitive Determination for Papain Conjugated CdSe Quantum Dots by Dynamic Light Scattering Analysis
Preparation and Characterisation of Surface Adsorbed Reduced Graphene Oxide/Polyaniline Nanocomposite on Polymer Membrane for Trimethylamine Sensing
Pressure Dependence of AZO Film Deposited by RF Powered Magnetron Sputtering System
One-Pot Synthesis of High Aspect Ratio Copper Nanowires in Aqueous Solution
Synthesis of Amorphous Fe-Doped SiO2 Anode Nanomaterial via Sol-Gel Method
Numerical Study of Adsorption Enhancement by Nanoparticles Scale Inhibitor
Synthesis and Surface Modification of ZnO Nanorods Arrays
Influence of Synthesis Conditions on the Properties of SnO2 Nano-Crystalline via Hydrothermal Methods
FCC Gasoline Upgrading over Modified Nanoscale HZSM-5 Catalyst
Effect of Surface Stress on the Deformation of an Half-Plane Applied to Nanometer Materials
Nano-Scale Friction of Multi-Phase Powder Metallurgy Tool Steels
Effect of Minimum Quantity Lubricant of Al203 Nanoparticle with SDBS on Surface Roughness during Turning of Mild Steel
Impact of Nanoparticles on Structure and Functional Properties of PBTG Biofilms
The Dynamic Mechanical Analysis of a Clamped-Free Timoshenko Nano-Beam Subjected to the Moving Force the Nonlocal Effects
Mobility Investigation of Nanoparticle-Stabilized Carbon Dioxide Foam for Enhanced Oil Recovery (EOR)
Study of Nanocrystalline ZnAl2O4 and ZnFe2O4 with SiO2 on Structural and Optical Properties Synthesized by Sol-Gel Method
Ag-Fe Alloy Nanoparticles Embedded in Polyaniline Nanocomposite Thin Films for E. coli Monitoring Sensor
On the Formation of Nanograined LiCo2O3(OH) Spinel-Type Material Synthesized via Modified Low-Temperature Sol-Gel Approach
Nanoclay as Anti-Blistering Agent in Polyester Based Coating: Effect of Sea Water and Distilled Water Exposure
Graphene-CNTs into Neuron-Synapse Like Configuration a New Class of Hybrid Nanocomposites
Optical and Morphological Properties of TiO2 Nanotubes for Sensor Applications
Nanofibrous Filters for Respirators
Acetylene Sensing Characteristics of SnO2 Nanowires
Controllable Growth of Highly Oriented ZnO Nanorod Arrays on Copper by a Two-Step Route
A Computational Chemistry Approach for Investigation of Low Friction Mechanisms Based on FEP Film with Functionalized SiO2 Nanoparticles
Synthesis of Zinc Oxide Nano Rods by Microwave Assisted Precipitation Method Using Polyacrylic Acid
Synergistic Effect of Graphene Nanoplatelets and Nanoclay on Epoxy Polymer Nanocomposites
Improved Nanoindentation Phase Transformation in Functional Structure of NiTi SMA and Graphene
Green Synthesis of Silver Nanoparticles Using Prunus Amygdalus Extract and their Anti-Microbial Activity
Nanoparticles Stabilized Carbon Dioxide Foams in Sandstone and Limestone Reservoir
Investigation on Voltage Breakdown of Natural Ester Oils Based-On Zno Nanofluids
Patterning of Polymer Arrays with Enhanced Aspect-Ratio Using Hybrid Substrate Conformal Imprint Lithography
Hybrid Hetero p-n Junction between ZnO Microspheres and p-Type Materials
Mechanism of Carrier Transport in n-Type -FeSi2/Intrinsic Si/p-Type Si Heterojunctions
Resistive Switching Properties of Zr, Ti, and Zn Metal Oxides
Chapter 2: Polymeric and Composite Materials and Their Properties
Optimization of Moulding Parameters on the Electrical Conductivity of Carbon Black/Graphite/Epoxy Composite for Bipolar Plateusing the Taguchi Method
Buckling Optimization of Composite Shells by Utilizing Finite Element Analysis, Neural Networks and Genetic Algorithm
Growth of Anodized Layer and Cerium Sealing on Al7xxx/SiC Composite
Mechanical and Morphological Properties of Buckminster Fullerene (C60) Added Glass Fiber Reinforced Polyamide 66 Multiscale Composites
Fracture Mechanism of Polypropylene-Kenaf Composite under Cyclic Loading
Reuse of Byproduct Alumina Composite Powder from Hydrogen Production Process
Comparative Study between SiC Reinforced Al 64430 Metal Matrix Composites and RHA Reinforced Al 64430 Metal Matrix Composites
Preparation and Performance Analysis of Mesh Hydroxyapatite/Sodium Alginate Composite Scaffold
Influence of Acid/Ether-Ratio on Composition and Dispersive Property of Polycarboxylic Type Water Reducers
Development of the Bending Actuator with Nafion-Pt IPMC Tube
Analysis of Mechanical Properties of Wood Dust Reinforced Epoxy Composite Using Response Surface Methodology
Biocomposite from Acrylonitrile-Butadiene-Styrene Polymer and Kenaf Whole Stem Fibre: Mechanical Properties
Molecular Dynamics Study of H2O Molecular Diffusion Behavior in PAM/PVA Polymer Blends
An Experimental Study on the Usage of Poisson's Ratio as a Damage Index
Flow Behavior of Wood Treated with Melamine Formaldehyde Resin under Non-Equilibrium Thermal-Compression
Mechanical Properties of Poly(Butylene Succinate) Reinforced with Alpha Cellulose
Compatibilization Efficiency of Reactively Modified Poly(butylene succinate) as a Compatibilizer for Poly(butylene succinate) Composites
Modification of the Mechanical Behavior in the Glass Transition Region of Poly(lactic acid) (PLA) through Catalyzed Reactive Extrusion with Poly(carbonate) (PC)
Effect of Fiber Content on Failure Modes of Glass Fiber Reinforced Injection Molded Polyamide 66 Composites
Effect of Particle Size of Natural Based Carbon Filler to the Absorbency of Superabsorbent Polymer Composite Synthesis by Graft Polymerization Method
Mechanical Properties and Thermal Behavior of TPS/PBS Blends with Maleated PBS as a Compatibilizer
Synthesis and Water Retention Properties of Poly(Acrylamide)-g-Kenaf Fiber Hydrogel
Chapter 3: Investigations in Rubber Based Materials
Electrical Characteristics of Silicone Rubber as Insulation Materials
A Study on Epoxidised Natural Rubber and Cis 1,4-Polybutadiene Blend
Electrospun Cellulose Acetate Fiber Containing Rubber Extract
The Influence of Agglomerators on Powdering of Chloroprene Rubber PCR-244
Research in Powdering Effects of Environmentally-Friendly Powder Rubber PSBR1500E
Influence of Modified Cassava Peel Waste (CPW) Loading on Tensile Properties of Natural Rubber Latex (NRL) Products
Cure Characteristics and Ageing Resistance of Recovered Waste Pre-Vulcanized Nitrile/Epoxidized Natural Rubber Latex Blends in Nitrile Butadiene Rubber Compounds
Chapter 4: Surface Engineering and Technologies of Coating
Transparent and Hydrophilic TiO2 Anatase as Top-Protective Layer for CSP Reflectors
Artificial Neural Network Modeling of Titanium Alloy Tribological Behaviour in Beta Solution Treated Condition
Fabrication and Evaluation of Corrosion Behavior of Nickel Alloy Metal Matrix Composite with Influence of Chills
The Effect of Styrene-Ethylene-Butadiene-Styrene on the Friction and Wear Properties of Polystyrene/Low Density Polyethylene Blends
Surface Modification on Vulcanized Rubber by DBD Plasma
The Novel Electroless Plating Process for Enhancing Coating Adhesion Strength
Non-Linear Insulator Performance of Wind Turbine Blade Surface against Lightning Strike
Chapter 5: Bio- and Eco Materials
Durability of Wood Shavel Composites with Environmental Friendly Based Binder
Response Surface Methodology to Optimize the Preparation of Chitosan/Alginate Nanoparticles Containing Curcumin Diethyl Disuccinate
Green Manufacturing of Eco-Materials by Urban Mining from Landfill Dump Site
Control of the Ozonation by-Products by O3/BAC in Shanxi Yellow River Water Treatment
Study on Gamma Irradiation on Sago Starch-Chitosan-PVA Blend Films
Synthesis of Biodegradable Polyester by Polycondensation with Tunable Properties
Surface Modification of 316 L Stainless Steel by Sol-Gel Ceramic Coating and its Cytocompatibility
Synthesis of Self-Healing Thermosetting Resin Based Capsules and their Related Complexities
Experimental Researches of Co-Cr Alloys Powders Manufactured by Sintering Process DMLS and Ni-Cr Alloys Used in Dentistry
Investigation of Ag Oxidation and Ion Adsorption on Small Intestinal Submucosa in Simulated Body Fluid through Simultaneous Electrochemical and SPR Measurements
Rapid Biomimetic Coating of Biocompatible Calcium Phosphate on Titanium: Influence of Pretreated NaOH Concentration and Cleaning Method
Chapter 6: Metals and Alloys, Industrial Chemical Technologies
Tuning the Microwave Dielectric Properties of Nd0.96Yb0.04(Mg0.5Sn0.5)O3 by Introducing Ca0.8Sr0.2TiO3
Mesoporous Titanium Dioxide Thin Films on Quartz via Electrochemical Anodisation Process
Predicting Methane Diffusivity in Polymeric Membranes by Molecular Dynamics
Crystallization of Aragonite from Vaterite Precursor during Various Refluxing Times
The Influence of Electric Parameters on Film Quality of GZO Thin Film Fabricated by APPJ Process
An Analysis of Burn Defect in Hard Anodized Process of AL 3003
Grafting of Linear Low Density Polyethylene (LLDPE) onto Tallow via Anhydride: Effect of Residence Time
Effect of Cerium Addition and Cooling Rate on Microstructure of ADC12 Eutectic Cast Alloy
Effect of Lanthanum Addition on Fluidity of Complex Al-11Si-Cu-Mg Cast Alloy
Effect of Lanthanum Addition on Microstructure and Hardness as Cooling Rate Function of ADC12 Eutectic Cast Alloy
Effect of HCl Concentration on the Phase and Microstructure of TiO2 Film Synthesized by Low-Voltage Anodization of Titanium
Effect of Zr, Nb and Ti Additions on Injection Molded 316L Stainless Steel: Microstructural, Mechanical Properties and Corrosion Resistance
Study of Mechanical Properties of Stainless Steel Oil Spill Plate on UG Finite Element Method
Effect of Different Operating Temperatures on Mechanical Properties of Several Rolled Aluminum Alloys
Effect of Processing Factors on the Bonding Strength of Fibrous Assembles by Dielectric Heating
Research on Heavy-Duty Coating Protection System of Magnesium Alloy
Caustic Magnesia Production in Microfluid Furnace
A Numerical Study on Stir Casting Process in a Metal Matrix Composite Using CFD Approach
Performance of Mixed Cellulase-Amylase Immobilized on PSF Membrane Support via Cross-Linked with Glutaraldehyde in Enzymatic Hydrolysis
Energy Analysis of Hydrogen Production from Methanol under Atmospheric Pressure and Supercritical Water Conditions
Preparation and Characterization of sPDVB/SPPO Composite Proton Exchange Membrane for Fuel Cell
Sulfate Ion Influence of LiNi1/3Co1/3Mn1/3O2 as Cathode Material for Lithium-Ion Batteries
Lost Circulation Material Characteristics of Apple Skin Powder in Drilling Mud
Effect of Alloying Elements and Impurity (N) on Bulk and Grain Boundary Cohesion in Cr-Base Alloys
Effect of Heat Treatment on Hardness and Microstructures of AISI 1045
Thermodynamic Analysis of the Effects of Alloying Elements on the Stacking Fault Energy in Ruthenium-Bearing Nickel Alloys
Effects of Al3+ and Zr4+ Cations on the Growth of Dendritic Lithium
Chapter 7: Technologies of Materials Processing
Sensitivity Analysis of Material Constitutive Model Parameters in Numerical Simulation of the Orthogonal Turning Process
Solid State Welding Process for Aerospace Components
Determination of Optimum Parameter Levels for Quality Characteristics in Conventional Drilling of Thick Polymeric Composites
Laser Surface Melting of Ti6Al4V Alloy with Ti-BN-C Mixed Powders
Processing of High Strength Magnesium Alloy with Enhanced Plasticity Using Squeeze Casting
Investigation into Effect of Cutting Conditions on Surface Roughness while Dry Machining Al-11%Si and Al-11%Si-1% Bi Die Casting Alloy
Surface Roughness Analysis of Carbon/Glass Hybrid Polymer Composites in Drilling Process Based on Taguchi and Response Surface Methodology
Evaluation of Two Different Energy Inputs for Deposition of Stellite 6 by Laser Cladding on a Martensitic Stainless Steel Substrate
Effect of Incremental Forming Process Parameters on Aluminum Alloy Using Experimental Studies
Surface Morphology and Wear Analysis of Stellite 6 Deposited on 9Cr-1Mo Steel Substrate by Laser Cladding
Chapter 8: Materials and Related Technologies in Construction
Porosity and Microstructure Phase of Self Compacting Concrete Using Sea Water as Mixing Water and Curing
Quasi-Static Lateral Crushing of Non-Woven Kenaf Fibre Reinforced Composite Hexagonal Tubes
Performance Evaluation of Lightweight Oilwell Cements
Characterization of Groundnut Husk Ash (GHA) Admixed with Rice Husk Ash (RHA) in Cement Paste and Concrete
Fibre Reinforced Concrete Class Control via Fib Model Code 2010 Approach
Mechanical Performance of a Plate Made by RC and Repaired through SFRC Material
Numerical Study on Uniaxial Compression Failure of Brittle Material with a Single Flaw
Influence of Inner Steel Tube Diameter on Compressive Behavior of Square FRP-HSC-Steel Double-Skin Tubular Columns
Lattice Boltzmann Modeling of the Effective Thermal Conductivity for Complex Structured Multiphase Building Materials
Residual Mechanical Parameters of Masonry Exposed to Fire: A New Numerical Approach
First Evaluation of the Structural Performance of Traditional Brickwork after Standard Fire Exposure
Frictional Loss of Prestress Caused by Locally Deflected Tendons in Prestressed Concrete Girder Bridges
Influences of Concentric and Eccentric Loads on Buckling of Fixed-End Supported Pultruded FRP Channel Beams
Response of Circular Footing on New Key Engineering Material - Granulated Blast Furnace Slag as Structural Fill
The Colorants Effects of Fe2O3 on Borosilicate Glasses Prepared from Subbituminous Fly Ash
Choice between Retrofitting and Reconstruction of Buildings in Reinforced Concrete after an Earthquake
A Demonstrated Net Zero Energy Building in Thailand: The Way for Sustainable Development in Buildings
Effect of Carbonation on the Sulfate Attack of Concrete Materials
C80 Early Strength Micro Expansion of Steel Tube Reinforced Concrete Research
Analysis on Energy Performance of Educational Facility by Composition of Double Glass
Influence of FRP-to-Concrete Gap Effect on Axial Strains of FRP-Confined Concrete Columns
Chapter 9: Physical Properties of Materials in Mechanical Engineering
The Effect of Mechanical Stress and Surface Tracking of 22 kV Cable Spacer
The Investigation of the Factors of the Fracture Toughness Based on the Compact Tension Specimen
Numerical Simulation of Spherical Indentation Method to Identify Metal Material Properties
Thermal Conductivity and Specific Heat Capacity of Different Compositions of Yttria Stabilized Zirconia-Nickel Mixtures
Experimental Verification of Effect of Adhesive Layer Thickness Used for Strain Gauge Mounting
Research on Damage Mechanism of Aluminum Foam Sandwich Plate Subjected to Blast Loading
The Mechanical Properties and the Influence of Parameters for Metallic Closed-Cell Foam Subjected to High-Strain Rates
Sintered SiO2 Modulus of Rupture Optimization by Means of Artificial Neural Networks
The Main Factors that Influence the Mechanical Properties of Honeycomb Board
Mechanical Properties of High-Strength Steel Obtained Using DIC for Specimens with a Hole
Recycled Plastic Quality Indicator Development Using Material Testing Results and Radar Chart
Finite Element Modeling of Effect of Adhesive Layer and Carrier Thickness Used for Strain Gauge Mounting
Silver-Mediated Perylene-3, 4, 9, 10-Tetracarboxylate Tetrapotassium Salt Aggregation for Highly Sensitive Detection of Iodide in Water
A Phenomenological Predictive Model for Thermo-Mechanical Fatigue of Notched Type 304 Stainless Steel
Study of Sodium Chloride's Effect on Warm Fog Dissipation and its Mechanism Research
Optimizing Detection Parameters of Magnetic Barkhausen Noise Using Heat Affected Zone in Welded Ship Steel Plate
by "Nielsen BookData"