2016 International Conference on Advanced Material Research and Application : selected, peer reviewed papers from the International Conference on Advanced Material Research and Application, August 13-14, 2016, Guilin, China
Author(s)
Bibliographic Information
2016 International Conference on Advanced Material Research and Application : selected, peer reviewed papers from the International Conference on Advanced Material Research and Application, August 13-14, 2016, Guilin, China
（Advanced materials research, v. 1142）
Trans Tech Publications, c2017
- : pbk
Available at / 1 libraries
-
No Libraries matched.
- Remove all filters.
Note
Includes bibliographical references and indexes
Description and Table of Contents
Description
This book collected from papers which were presented on International Conference on Advanced Material Research and Application (AMRA2016, 13-14 August, Guilin, China). The goal of this conference was the presentation of last researches and solutions in the field of materials science including, alloy materials, polymers, composite materials, nanomaterials, structural materials, synthesis and processing technologies.
Table of Contents
Preface, Committees, Sponsor
Chapter 1: Metals and Alloys
The Valence Electron Structure of High-Entropy Alloys
Deliquescence of NaCl and Atmospheric Corrosion of 316L Stainless Steel
Research on the Structure of GdFeMn Compound
Role of Bulky Retained Austenite in Austempered Ductile Iron
Effect of Frequency on the Fatigue Behavior of IN718 Superalloy
Study on the Performances Properties of Medical Pure Magnesium by Ion Implantation of Nitrogen
Phase Purity and Thermoelectric Properties of Type-I Clathrates Ba8CuxSiyGe46-x-y (4 x 6.5, y = 0 and 5.15 x 6.425, 2.05 y 36.9)
Chapter 2: Magnetic Materials
Magnetic Properties and Magnetocaloric Effect of Nd0.7Gd0.3Mn2Si2 Alloy
The Effects of Substitution of Nd by Gd on the Magnetic Properties of Melt-Spun Nd-Fe-B
Microstructure and Magnetic Properties of (Nd0.7Pr0.15RE0.15)2.28Fe13.58B1.14 (RE=La, Ce, Y) Alloys
Thermodynamic Calculation of the Heavy Rare Earth Permanent Magnets: Fe-RE (RE=Gd, Tb, Dy, Lu) Binary Systems
Chapter 3: Materials for Optoelectronics
Synthesis and Photochromic Properties of 1-[2-Cyano-1,5-Dimethyl-4-Pyrryl]-2-[2-Methyl-5-(1,3-Dioxolane)-3-Thienyl] Perfluorocyclopentene
Synthesis, Photochromism Properties of 1-(1,5-Dimethyl-2-Pyrrolecarbonitrile)-2-[2-Methyl-5-(4-Aminomethyl)Phenyl-3-Thienyl] Perfluorocyclopentene
Preparation and Luminescent Properties of 0.1%Ce3+:BaF2 Laser Ceramics by Vacuum Sintering
Study on the Synthesis and Application of a Material 1-[2-Methyl-5-Phenyl-3-Thienyl]-2-[2-Methyl-5-(3-Aldehyde-4-Methoxy)-3-Thienyl] Perfluorocyclopentene
Chapter 4: Solar Cells
A Novel Strategy for Preparation of Cu2(MII)(MIV)S4 Thin Films for Solar Cell: Sulfurization of Mixed Metal Oxides Precursor Synthesized by Combustion Method
Chapter 5: Synthesis and Properties of Ceramics
Implementation Mechanochemical Synthesis of Titanium Carbide in the Presence of Carbon Components from Plant Raw Material and Graphite
Dynamic Impact Induced Residential Stress and Deformation in Silicon Carbide Ceramics
Research Progress on Joining of Cf/SiC to Metals
Chapter 6: Polymers and Composites
Rapid and Reversible Hybrid Organogels Induced by Solvent Response
Effect of Temperature on Conductivity Performance of PEO-NaI Based Polymer Electrolytes
Micro-Hardness Test of Cross-Linking LLDPE
Pyrolysis Behaviour of Boron Phenolic Resin-Based Ceramicable Composites by Introducing of MgO-Al2O3-SiO2
Study on Tensile Mechanical Behavior of Composite T-Joints
Effects of Meso-Structure in Grinding of 2.5D Woven Fiber-Reinforced Ceramic Composites
Chapter 7: Technologies for Production of Thin Films and Coatings
The Study of High Temperature Oxidation Performance of Thermal Barrier Coatings Prepared by Plasma Spraying and Laser Remelting
Oxidation Resistance and Insulation of AlPO4/Al2O3 Coating on Tungsten Substrate at High Temperature
Effect of PTFE Content on Microstructure and Tribological Properties of Cu-Sn Coating
Study on Wear Resistance of Two Types of Low Phosphorus Electroless Nickel Plating on 30CrMnSi
Material Design and Experiment Test of a High-Impedance Complex Film
The Effect of Different Methods of Modification on the Surface Properties and on the Finale Strength of Bonded Joints of Selected Types Thermoplastics
Chapter 8: Nanomaterials
Preparation of NixCo3-xTiO4 Ternary Nanowire and Study on their Electrocatalytic Performances
Preparation and Properties of Ethylene Propylene Diene Rubber/SiO2/Carbon Nanotubes Composites
Effect of Carbon Nanotube Content on Properties of Ethylene Propylene Diene Rubber/CaCO3/ Carbon Nanotube Composites
Microwave Absorption Properties of BaFe12O19 Prepared in Different Temperature with Polyaniline Nanocomposites
Optimization of NDV Encapsulated in N-2-HFCC/CMC Nanoparticles Preparation Conditions
Synthesis and Characterization of Thiol- and Carboxyl-Functionalized Mesoporous Silica Nanoparticles
One-Step Hydrothermal Reduction and Functionalization of Graphene Oxide with a Modified Diethylene Triamine
Intercalation of Fenoprofen into Layered Double Hydroxide for the Formation of Controlled Release Anti-Inflammatory Drug
Core-Shell Au-Pt Nanoparticles and Nanodendrites for Methanol Oxidation Reaction
Chapter 9: Materials Processing Technologies
Research on Worktable Control of the Mask Exposal Forming Machine
Stress-Strain Behavior of an Octahedral and Octet-Truss Lattice Structure Fabricated Using the CLIP Technology
Cutting Performance of Fiber Laser Textured Tools in Face Milling of Titanium Alloys
Research on Process and Property of H13 Die Steel Directly Manufactured by Selective Laser Melting
The Influence of Cu/Ti Overlapping Region Microstructures on the Mechanical Tensile Properties of the Joint via Friction Stir Lap Welding
Machining of SiCp/Al Composites: Effect of Tool Corner Radius on Residual Stresses, Cutting Force and Temperature
Research on the Mechanical Performance and Crack Defects Assessment of X65 Marine Pipeline Welding Joint
Numerical Simulation of Flow and Heat Transfer for Cooling Roller in Amorphous Spinning Process
Chapter 10: Materials and Technologies in Environmental Engineering and Chemical Manufacturing
Preparation of Polyaniline/Cotton Composite for Cr (VI) Removal in Solution
Study on the Stabilization/Solidification of Lead-Contaminated Soil Using Alkali-Activated Cementing Materials with Rich-Silicon Materials
Stabilization of Cd in Ore Soil Using Modified Red Mud Materials
Mechanistic Insight into H2S Adsorption and Dissociation on MoP(010): A Density Functional Investigation
Experimental Study on the Emergency Disposal Agent for Methanol Leakage
Chapter 11: Building Materials
A Comparison Study of the Rapid Setting Conventional and Polymer-Modified Waterproof Mortars
The Study of Preparation Technology of the Material Saving Plastic Building Moulding Board
An Experimental Research on Basic Properties of Ceramsite Cellular Concrete
Research on Performance of CRTS I Cement-Emulsified Asphalt Mortar on Site
Study on the Aging and Pore Structure of Hydraulic Concrete
The Improvement of Deformation Analysis for Circular Tunnel Based on Hoek-Brown Criterion in Strain-Softening Rock Mass
Extended Constitutive Model for FRP-Confined Concrete in Circular Sections
Chapter 12: Testing and Assessment of Materials in Mechanical Engineering
Research on Material Damage Modes of Escalator Drive Chain
Numerical Simulation of Gun Bore Damage during Engraving Process of Driving Band
Application of Hypotheses Theory during Creep Curves Assesment
Nonlinear Ultrasonic Properties of Stress in 2024 Aluminum
by "Nielsen BookData"