松村 隆 MATSUMURA Takashi

ID:1000020199855

東京電機大学 Tokyo Denki University (2015年 CiNii収録論文より)

Search authors sharing the same name

Articles:  1-20 of 109

  • S1360103 Cutting force analysis in whirling machining  [in Japanese]

    SERIZAWA Masaki , MATSUMURA Takashi

    Whirling cut has been applied to machining of worm and ball screws for motion controls. The whirling cut, in which the tool and the workpiece rotate simultaneously with an eccentricity between the cen …

    The Proceedings of Mechanical Engineering Congress, Japan 2015(0), _S1360103--_S1360103-, 2015

    J-STAGE

  • 28pm3-B-5 Micro drilling on thin wires for micro devices  [in Japanese]

    Serizawa Masaki , Matsumura Takashi

    Micro drillings on thin wires are presented to manufacture the micro devices. 0.15 mm drill holes drill holes were machined on the side of 0.3 mm diameter titanium alloy wires with an end mill and a d …

    The Proceedings of the Symposium on Micro-Nano Science and Technology 2015.7(0), _28pm3-B-5-_28pm3-B-5, 2015

    J-STAGE

  • 20am2-E1 Micro machining on thin wires for micro device  [in Japanese]

    Serizawa Masaki , Matsumura Takashi

    Micro milling on thin wires is presented to manufacture the parts in micro devices. The micro cutting and grooving are conducted on 0.2 and 0.3 mm diameter stainless wires with a square and a ball end …

    The Proceedings of the Symposium on Micro-Nano Science and Technology 2014.6(0), _20am2-E1--_20am2-E1-, 2014

    J-STAGE

  • S1320204 Grooving of Unidirectional Carbon Fiber Reinforced Plastics  [in Japanese]

    TAMURA Shoichi , MATSUMURA Takashi

    When a CFRP (Carbon Fiber Reinforced Plastics) plate, which is light weight and high strength composite material, is machined with a cutting tool, the surface integrity depends on the cutting directio …

    The Proceedings of Mechanical Engineering Congress, Japan 2014(0), _S1320204--_S1320204-, 2014

    J-STAGE

  • S1320104 Turning process in whirling  [in Japanese]

    SERIZAWA Masaki , MATSUMURA Takashi

    Difficult-to-cut materials such as titanium alloy have recently been used in the aircrafts and the medical fields. The tool life is a critical issue in cutting of the difficult-to-cut materials. In or …

    The Proceedings of Mechanical Engineering Congress, Japan 2014(0), _S1320104--_S1320104-, 2014

    J-STAGE

  • A10 Tool wear characteristics in drilling of CFRP/Titanium alloy stacks  [in Japanese]

    Tamura Shoichi , Matsumura Takashi

    The paper discusses tool wear characteristics in drilling of CFRP stacked on Ti-6Al-4V. A cutting simulation was applied to prediction of the cutting force, the cutting temperature and the tool wear. …

    The Proceedings of The Manufacturing & Machine Tool Conference 2014.10(0), 15-16, 2014

    J-STAGE

  • A04 Helical blade machining in whirling  [in Japanese]

    Serizawa Masaki , Matsumura Takashi

    Whiling is applied to helical plate machining with controlling the spindle speeds of the workpiece and the tool. When the ratio of the tool spindle speed to the workpiece one is 2, a plate type blade …

    The Proceedings of The Manufacturing & Machine Tool Conference 2014.10(0), 5-6, 2014

    J-STAGE

  • 7PM1-D-1 Micro dimple machining with small diameter end mill  [in Japanese]

    Musha Yuji , Matsumura Takashi

    A micro dimple machining is studied to control the surface functions with the micro-scale structures on the solid surfaces. The micro dimples are machined in milling with the inclined ball end mill. W …

    The Proceedings of the Symposium on Micro-Nano Science and Technology 2013.5(0), 285-286, 2013

    J-STAGE

  • S132024 Orthogonal Cutting of Rolled Titanium Alloy  [in Japanese]

    TAMURA Shoichi , MATSUMURA Takashi

    The machining technologies of titanium alloys are required to reduce the production time and cost for the titanium products. Anisotropy of the titanium alloy plate is discussed in the orthogonal cutti …

    The Proceedings of Mechanical Engineering Congress, Japan 2013(0), _S132024-1-_S132024-3, 2013

    J-STAGE

  • S132013 Machining of Helical Blades in Whirling  [in Japanese]

    SERIZAWA Masaki , MATSUMURA Takashi

    Machining of helical plates such as blades has recently been increased with manufacturing of the aircrafts and the energy facilities. The high machining rate and the stable machining have been require …

    The Proceedings of Mechanical Engineering Congress, Japan 2013(0), _S132013-1-_S132013-3, 2013

    J-STAGE

  • F222004 Micro Mechanical Machining and Applications  [in Japanese]

    MATSUMURA Takashi

    Micro machining of glass is required for manufacturing of glass devices such as micro TASs. However, some issues have been left on the flexibility, the machining costs and the environmental impact in …

    The Proceedings of Mechanical Engineering Congress, Japan 2012(0), _F222004-1-_F222004-3, 2012

    J-STAGE

  • S134023 Cutting Simulation in Drilling of Anisotropic Materials  [in Japanese]

    MATSUMURA Takashi , TAMURA Shouichi

    A force model is presented to predict the cutting force in drilling of anisotropic materials. The cutting process of rolled titanium alloy depend on the edge orientation with respect to the rolling di …

    The Proceedings of Mechanical Engineering Congress, Japan 2012(0), _S134023-1-_S134023-3, 2012

    J-STAGE

  • OS2-2-3 Micro Mechanical Machining of Surface Structure for Control of Wettability  [in Japanese]

    Matsumura Takashi , Sasajima Kanae

    Machining process is presented to control wettability on surfaces with micro structures. The structure elements are machined by cutting with a small diameter end mill. Then, the top of the structure e …

    The Proceedings of the Symposium on Micro-Nano Science and Technology 2012.4(0), 147-148, 2012

    J-STAGE

  • OS2-1-2 Machining of Micro Screw in Whirling Process  [in Japanese]

    Matsumura Takashi , Serizawa Masaki

    Whirling is applied to machining of micro screws on wires. The whirling process, which is usually performed to manufacture ball screws, is described in terms of the cutting mechanism. Because the mate …

    The Proceedings of the Symposium on Micro-Nano Science and Technology 2012.4(0), 109-110, 2012

    J-STAGE

  • B32 Drilling of CFRP/Ti6A14V with step drills  [in Japanese]

    Tamura Shoichi , Kondo Hiroyasu , Matsumura Takashi

    In drilling of Ti6A14V stacked CFRP, the chip flow should be controlled to finish the hole without any damages on the surface of the CFRP layer. A step drill is applied to drilling of Ti6A1 V stacked …

    The Proceedings of The Manufacturing & Machine Tool Conference 2012.9(0), 125-126, 2012

    J-STAGE

  • B30 Peripheral milling of glass plate  [in Japanese]

    Matsumura Takashi , Maneyama Hiroki

    Demand of touch panels have been increasing in the mobile device. However, damages of the glass panels are one of the critical issues in the practical uses. Therefore, composite materials of plastic a …

    The Proceedings of The Manufacturing & Machine Tool Conference 2012.9(0), 123-124, 2012

    J-STAGE

  • B29 Micro milling of sapphire  [in Japanese]

    Matsumura Takashi , Yamaguchi Tetsuya

    Micro cutting of sapphire is presented to finish crack-free surfaces in planing and milling. m crystal plane is cut with measuring the cutting force and observing the surface finish in planing. The cu …

    The Proceedings of The Manufacturing & Machine Tool Conference 2012.9(0), 121-122, 2012

    J-STAGE

  • B25 High speed cutting of surface texture  [in Japanese]

    Matsumura Takashi , Blanchet Jerome

    simultaneous controlled cutting is presented to fabricate micro-scale textures on surfaces at high machining rates. The surface texture is machined with rotations of the workpiece and the tool on a tu …

    The Proceedings of The Manufacturing & Machine Tool Conference 2012.9(0), 115-116, 2012

    J-STAGE

  • Machining of Micro Glass Devices in Milling  [in Japanese]

    MATSUMURA Takashi

    Journal of the Society of Mechanical Engineers 115(1128), 758-761, 2012

    J-STAGE References (8)

  • 2-3 Glass Milling and Applications  [in Japanese]

    Matsumura Takashi

    Micro machining of glass is required for manufacturing of glass devices such as micro TASs. However, some issues have been left on the flexibility, the machining costs and the environmental impact. Th …

    The Proceedings of the Symposium on Micro-Nano Science and Technology 2011.3(0), 17-18, 2011

    J-STAGE

Page Top