AIAA aerospace design engineers guide
著者
書誌事項
AIAA aerospace design engineers guide
American Institute of Aeronautics and Astronautics, 1998
4th ed
大学図書館所蔵 件 / 全6件
-
該当する所蔵館はありません
- すべての絞り込み条件を解除する
注記
Includes bibliographical references
内容説明・目次
内容説明
Revised and reformatted in a lay-flat binding for ease of use, this edition features enlarged figures, charts and tables for legibility. The guide provides a condensed collection of commonly-used engineering reference data related to aerospace design. New material on helicopter design and radar cross section has been added to this edition. This work is intended for design engineers and aerospace students.
目次
- Part 1 Mathematics: Greek Alphabet
- SI Prefixes
- Algebra
- Trigonometry
- Mensuration
- Analytic Geometry
- Differential Calculus
- Integral Calculus
- Differential Equations
- Complex Quantities
- Some Standard Series
- Matrix Operations
- Determinants
- Curve Fitting
- Small-Term Approximations
- Vector Equations. Part 2 Section Properties: Plane Areas
- Solids
- Shells. Part 3 Conversion Factors: Length (l)
- Area (A)
- Volume (V): Plane Angle (q)
- Solid Angle
- Mass (m)
- Density
- Time (t)
- Velocity (v)
- Force (F)
- Pressure (p)
- Energy, Work, Heat (W)
- Power (P)
- Thermal Conductivity (k)
- Absolute or Dynamic Viscosity (m)
- Inductance (L)
- Kinematic Viscosity (v=m/r)
- Capacitance (c)
- Electrical Resistance (R)
- Electrical Resistivity, Reciprocal Conductivity (P)
- Magnetic Field Intensity (H)
- Magnetomotive Force
- Magnetic Flux (f)
- Magnetic Flux Density (B)
- Machine Screws - Tap Drill and Clearance Drill Sizes
- Decimal Equivalents of Drill Size
- Standard Gages. Part 4 Structural Elements: Beam Formulas
- Torsion Formulas - Solid and Tubular Sections
- Torsion Formulas - Thin-Walled Open Sections
- Position of Flexural Centre Q for Different Sections
- Buckling and Stress
- Columns
- Plates
- Rivets
- Bolt and Screw Strengths
- Vibration
- Forced Vibration
- Beam Natural Frequency
- Plate Natural Frequency. Part 5 Mechanical Design: Spring Nomenclature
- Helical Springs
- Springs
- Basic Formulas for Involute Gears
- Coefficients of Static and Sliding Friction
- Bevel Gears
- Worm Gearing
- Epicyclic Gearing
- Formulas for Brakes, Clutches and Couplings
- Pump Relationships
- Approximate Relative Impeller Shapes and Efficiencies as Related to Specific Speed
- Control System Loads
- Dynamic Stop Loads
- Friction of Pulleys and Rollers
- Cables
- Bearings and Bushings
- General Bearing Characteristics
- Airframe Bearings Friction Torque
- Rods and Links
- Shafts
- Pins
- Actuators
- Cylindrical Fits
- Key Joints
- Kinematics. Part 6 Electrical/Electronics: Symbol Definitions
- Ohm's Law
- Wire Chart
- Resistor Colour Codes
- Properties of Insulating Materials
- Connections
- Information Exchange Code
- Interface Connector Pin Assignments per RS-232-C
- Resistor, Capacitor, Inductance Combinations
- Dynamic Elements and Networks
- Laplace Transforms
- Voice Transmission Facilities
- Electromagnetic Spectrum
- Antennas
- Frequency Classifications
- Radar Letter-Band Nomenclature
- Radar Range Equation
- US Electronic Equipment Designations. Part 6 Aircraft Design: Vehicle Definitions
- Aerodynamics
- Radar Cross Section
- Propulsion
- Performance
- Helicopter Design
- Bibliography. Part 7 Geometric Dimensioning and Tolerancing: ANSI/ASME Y14.5M-1994
- Abbreviations and Acronyms
- Definitions. (Part Contents)
「Nielsen BookData」 より