Structural integrity and failure : selected, peer reviewed papers from the International Conference on Structural Integrity and Failure (SIF 2010) July 4-7, 2010, Held at the University of Auckland, Auckland, New Zealand

著者

    • International Conference on Structural Integrity and Failure
    • Ferguson, George

書誌事項

Structural integrity and failure : selected, peer reviewed papers from the International Conference on Structural Integrity and Failure (SIF 2010) July 4-7, 2010, Held at the University of Auckland, Auckland, New Zealand

edited by George Ferguson ... [et al.]

(Advanced materials research, v. 275)

Trans Tech Publications, c2011

大学図書館所蔵 件 / 1

この図書・雑誌をさがす

注記

Includes bibliographical references and indexes

内容説明・目次

内容説明

Volume is indexed by Thomson Reuters CPCI-S (WoS). This special collection of 59 peer-reviewed papers covers topics related to the fracture and fatigue of all types of materials and structures, including biological tissues, metals, ceramics, polymers, composites and thin films. This wide range of coverage will make this work of interest to those studying almost any sort of material.

目次

Preface and Organizing Committee I. Fracture, Fatigue, Damage and Failure An Artificial Neural Network Approach to Fatigue Crack Growth Experimental Investigation of PMMA Fracture under Mixed-Modes I, II and III Loading Modelling Fatigue Crack Growth near an Open Hole under Spectrum Loading Using a New Method for Elastic-Plastic Stress Calculation Effects of Crack Size and Crack Face Interference on Shear Fatigue Crack Growth in a Bearing Steel A Model for the Cyclic Behaviour of Steel under Earthquake Conditions Fatigue Strength of Ultrafine Grained Copper Treated by Post-ECAP Mild Annealing Experimental Study on Theory of Critical Distance Applied to the Prediction of Fatigue from Notches Effects of Thermal Exposure on Microstructure and Mechanical Properties of Ni Based Superalloy GTD111 Effects of Replication on Measured S-N Curves of Metals Fatigue Behavior of Weld-Repaired High Strength Low Alloy Steel An Analysis of Fatigue Strength of Notched Components Thermal Shock Properties of Ti(Al,O)/Al2O3 and TiAl(O)/Al2O3 Composite Coatings An Impregnation Technique for Crack Identification Following Uniaxial Tension Tests An Analysis of the Bonding Energy through Pull-Out Tests for Aerated Concrete with Various Steel Strip Geometries Low Cycle Fatigue Behavior of Ni-Base Superalloy IN738LC at Elevated Temperature II. Structural Integrity & Failure Analysis Study of Local Failure of a Multi-Plate Arch Bridge by Numerical Modeling Assembly Deformation and Stresses of Compliant Structures Fracture Strengths of Mg Alloy AZ31B-H24 Friction Stir Lap Welds Effect of Tool Speeds during Friction Stir Lap Welding on Mode of Fracture and Fracture Strength of Al 6060-T5 Joints Characteristics of Electron Beam Welded Ti & Ti Alloys Microindentation of Microencapsulated Phase Change Materials Light Emission from a Si Based ZnO Structure Managing Potlife through Statistical Analysis Stress and Vibration Analysis of Motor Back Plate in HDD Aircraft Joints: the Interaction between Corrosion Protection and Structural Performance Residual Strength Optimisation of a Vent Hole in an Aircraft Component Using a Heuristic Method Influence of Heat Treatment on Fatigue Strength of Drawn Steel Tubes for Small-Sized Single Pass Boiler The Microstructure and Mechanical Properties of Ni-Based Superalloy after Service Exposure in Gas Turbine Degradation Characteristics of Inconel738LC with Thermal Exposure Effects of High Temperature Deformation and Thermal Exposure on Microstructure and Mechanical Properties of Co-Based Superalloy Optimum Design for Life Extension on the End Coupling of Aluminum Hot Rolling Process Integrity Evaluation and Dynamic Behavior of Radioactive Material Transport Cask under Drop Impact III. Bio and Nano-Materials Ab Initio Phonon Dispersion Curves Used to Check Experimentally Determined Elastic Constants of the MAX Phase Ti3SiC2 Failure Mechanisms of Cartilage-on-Bone Tissues and the Influence of Loading History Processing of Layered Hydroxyapatite Ceramic Composites Nanoindentation of Individual ZnO Nano-/Micro-Rod Validation of BioDent TDI as a New Clinical Diagnostic Method Effect of Heat Treatment on Microstructure and Mechanical Properties of a Ti-Mo-Zr Alloy IV. Indentation, Thin Film, Surface Treatment & Materials Processing Copper Coated Iron Powder Prepared by Chemical Reduction Process Study of Preparation on the Flake Silver Coating over Copper Powder for Electronic Industry Mechanical Behaviour of Ultrafine Grained Cu and Cu-(2.5 and 5) Vol.%Al2O3 Composites Produced by Powder Compact Forging Friction and Wear Characteristics of SUS304 and SUS630 after Ultrasonic Nanocrystal Surface Modification Wear Evaluation of SiCp Reinforced Al Matrix Composites Coatings Improvement of Biocompatibility of Medical Ni-Ti Alloys through Forming TiO2 Thin Film Mechanical Behaviour of Titanium, Ti-6Al-4V (wt %) Alloy and Ti-47Al-2Cr (at %) Alloy Produced Using Powder Compact Forging Influence of Growth Rate on the Solute Distribution of Directionally Solidified Cu-Ag-Zr Alloy Tensile Properties and Fracture Behaviour of Induction Sintered Ti and Ti-6Al-4V (wt %) Powder Compacts Phase Composition, Microstructure and Thermal Diffusivity of Cu/Si Composites Sintering Temperature Dependence Tool Wear Mechanisms during Machining of Alloy 625 Microstructure and Mechanical Behaviour of Ultrafine Grained Al-4wt%Cu-(2.5-10) Vol.% SiC Metal Matrix Composites Produced by Powder Compact Forging Effect of Pb and Sn Additions on the Ductility of Cast AZ61 Mg Alloy Cracking and Mechanical Strength of NaOH-Slag Geopolymers Microstructure Evolution in Nitrogen Implanted Sapphire V. Polymers and Composites Fracture Toughness of Polyamide 6/ Maleated Styrene-Ethylene-Butylene-Styrene/Silicon Carbide Nanocomposites Reliability Analysis for Inserts in Sandwich Composites Experimental Study on Strengthening of Steel Structures with Fiber Reinforced Plastic The Influence of Processing Parameters on the Void Content and Compressive Strength of Carbon Fibre-Epoxy Laminates Strength and Fracture Behavior of Abaca Green Composites Microstructure and Hardness of Ni-Cr Porous Preform Reinforced Al-Based Composites by Low Infiltration Method

「Nielsen BookData」 より

関連文献: 1件中  1-1を表示

詳細情報

  • NII書誌ID(NCID)
    BB06862551
  • ISBN
    • 9783037851760
  • 出版国コード
    sz
  • タイトル言語コード
    eng
  • 本文言語コード
    eng
  • 出版地
    Durnten-Zurich
  • ページ数/冊数
    xii, 260 p.
  • 大きさ
    25 cm
  • 親書誌ID
ページトップへ